Extra Fine Clear Anti-Slip Spray for Wood

SlipDoctors

  • $30.00


Our Extra Fine Clear Spray anti-slip solution is an epoxy aerosol spray that provides a clear, hard, finely textured finish on wood and vinyl surfaces. It is virtually invisible, barefoot-friendly and paw friendly, lead-free and chemical resistant.

Ideal for use on both interior and exterior surfaces where slip resistance is needed. This convenient, easy-to-apply aerosol spray is the perfect solution to treat small or irregularly shaped surfaces and can be used on vinyl, linoleum, wood and many other surfaces. One can covers up to 20 sq. ft.

Installation Instructions (TDS) Safety Data Sheet (SDS)


Suggested Uses

  • Residential & Commercial Use
  • Wet Areas 
  • Entrances/Exits 
  • Restrooms 
  • Wood Stairs 
  • Wood Decks 
  • Foyers

Special Features 

  • Interior & Exterior Use 
  • Barefoot Friendly 
  • Increases Traction 
  • Durable 
  • Easy to Clean 
  • Weather Resistant 
  • Fast & Easy Application
Single Case
Coverage per Sq Ft 20 240
Cost per Sq Ft (Appx.) $1.50 $1.40

Safety Precautions:
• Extra Fine Non-Slip Spraymust be used in a well-ventilated area.
• Never use Extra Fine Non-Slip Spray near an open flame.
• If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC. Contact the National Lead Hotline at 1-800-424-LEAD or www.epa.gov/lead

Recommended Safety Equipment:
• Chemical-resistant gloves
• Eye protection
• Mask

Surface Preparation:

Varies by surface. Please see chart below for preparation for specific surfaces. ALWAYS: Test a small area for color compatibility and adhesion. For best results, spray between 70-90°F / 20-32°C. Applying SlipDoctors’ Non-Slip Spray below 50°F/10°C will cause the paint to spray and/or dry improperly. Dry time decreases with higher temperatures and increases with lower temperatures.

Application Instructions:

Step 1: TEST: Extra Fine Clear Spray should be tested on a small inconspicuous areabefore full application.
Step 2: MIXING: Mix contents of can well by shaking until the ball rattles within the can. Once ball rattles, continue to shake vigorouslyfor 2-3 minutes. During use, shake intermittently for 10 seconds to keep product mixed.
Step 3: APPLICATION:Spray 6-12 inches away from surface in a sweeping motion during application. When applying, note that 2-3 light coats will cure, protect and look better that one heavy coat.
Step 4: If spray stopsor is irregular, turn can upside down and spray for 2-3 seconds to clear nozzle. Wipe tip, shake can and resume. IMPORTANT: Before storing partial can, clean valve immediately afteruse. To clean: Hold can upside down and spray until only clear gas comes out (approximately 3seconds), then wipe tip and store. If spray nozzle becomes clogged, remove and clean in lacquer thinner.
Step 5: CLEAN UP: If overspray occurs, area can be cleaned with paint thinner.

Maintenance:

For best results,to remove oily deposits or other foreign matter, apply pH-neutral cleanerat recommended dilution rate and scrub lightly with a soft bristle brush. For general cleaning and maintenance, use a light-pressure rinsing.

Customer Reviews

Based on 20 reviews
85%
(17)
15%
(3)
0%
(0)
0%
(0)
0%
(0)
P
P.K.
Thank you for taking the time to review our product. Team SlipDoctors
T
T.K.
Thank you for taking the time to review our product. Team SlipDoctors
S
S.B.
Perfect for Elderly Pets
Thank you for taking the time to share your feedback. Team SlipDoctors
L
L.C.
Exactly What I Was Looking For
Thank you for purchasing our product and for sharing your experience with us and the community.
P
P.H.
Does the job
Thank you for taking the time to review our product. Team SlipDoctors

Customers Who Purchased This Item Also Viewed


Sale

Unavailable

Sold Out