Deck Grip - Clear Indoor & Outdoor Non-Slip Sealer for Concrete
Deck Grip is an anti-slip sealer for concrete and other stone surfaces. This versatile non-slip coating is non-yellowing, water-based acrylic and is easy to apply. Deck Grip non-slip concrete results in a clear, semi-gloss and barefoot-friendly finish that is chemical resistant, UV resistant and highly durable. Deck Grip is the perfect anti-slip solution to treat slippery pool decks, and all types of stamped (sealed or unsealed) concrete decks. Compatible on virtually all types of natural stone surfaces where anti-slip sealers are desired.
Deck Grip Roller - Click here to buy more
Sealed Stamped Concrete - Deck Grip will work great on top of all sealers and is chemical and chlorine resistant. Ideas for surfaces surrounding pools and spas. Please start with a clean dry surface prior to application. Allow 24 hours to cure. Apply 2 thin coats for best durability and slip resistance. NOTE: Some textured surfaces require 3 coats for best traction.
Even when wet, your slippery floor’s slip resistance after the non-slip solution will surpass ANSI A137.1, A326.3 or B101.3 standards.
0.52 Wet DCOF - ANSI B101.3
0.53 Wet DCOF – ANSI A137.1 / A326.3
0.62 Wet SCOF - ANSI B101.1
- Great for bare feet
- Use it on pool decks and sealed concrete
- One 3/8” nap roller included per gallon
- Deck Grip is available in 1 gallon and 5-gallon pails
- Can be used indoors or outdoors
- It dries clear with a semi-gloss finish and is easy to apply
- One gallon covers 300 – 600 square feet
- Roller Included (Click here to buy more)
|Coverage per Sq Ft||300-600||Appx 2,500|
|Cost per Sq Ft (Appx.)||$0.25||$0.23|
|⅜” Nap Rollers Included||1||5|
• Use in a well-ventilated area.
• If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC. Contact the National Lead Hotline at 1-800-424-LEAD or www.epa.gov/leadfor more information.
Optional Safety Equipment:
• Chemical-resistant gloves
• Eye protection
• Surface preparation varies by surface. Please see chart below for specific surface preparation instructions.
Step 1: Mixing Additive: The quantity of SlipDoctors Deck Grip Additive to be used depends on the level of slip resistance desired(see chart below). Maximum texture is recommended for the most effective anti-slip protection. Pour desired amount of Additive into Deck Grip container and gently mix to ensure even distribution. Avoid shaking to prevent foaming. Mix occasionally during application.
Step 2: TEST: Deck Grip should be tested on a small inconspicuous area before full application
Step 3: Deck Grip can be rolled or sprayed, rolling is recommended. Roll: Use the included3/8” nap roller to evenly coat the surface. Avoid puddling in low areas. If puddles occur, roll them out. Two thin coats are recommended rather than one thick coat. Spray: Spray using a 5916 nozzle that produces a flow of 1/10 of one gallon per minute. Spray in a fine fog pattern without spurts or dribbles to form a thin continuous film. Avoid puddling in low areas. If puddles occur, roll them out.
Step 4: For added protection, greater performance and durability,we recommend applying Deck Gripin two thin coats. Allow first coat to dry for 2-4hours before applying the second coat. The second coat should be applied at a right angle to the first coat.
Step 5: Clean-up:While Deck Gripis still wet, equipment may be cleaned with soap and water. Once dried, equipment may be cleaned with a solvent, such as xylene or toluene.
For general cleaning and maintenance,use a light pressure rinsing. For best results to remove oily deposits or other foreign matter, apply pH-neutral cleanerat recommended dilution rate and scrub lightly with a soft bristle deck brush.Do not use alcohol-based cleaners, such as pine-sol.
Our newly painted patio was slick as glass when wet. Three coats of Deck Grip and the patio is no longer slick when wet. Great product and customer service was great. We called a couple of times with questions and they were extremely knowledgeable and helpful.
The slip Doctor product went on very easy, follow their directions and you will have a non slip concrete floor that looks great!
We’ve had a few near falls on the slippery travertine around our pool in the past, but adults have learned to step from the cool deck into the pool. With little grandkids in the picture now, we needed a solution. After three coats of Deck Grip, the travertine isn’t slippery when wet any more. I appreciate the peace of mind this gives!!! I also prefer the wet look it has now. The product was easy to apply and Slip Doctors employees have been extremely helpful and responsive.
My 3 year old son was slipping on our stamped concrete around our pool. One day he was just standing and fell flat on his face and busted his lip. So we knew we needed to do something. There is plenty for multiple coats, and it works pretty well. I still need to do a wet test on myself, but the micro grit seems to add a layer of grip that previously was not there. I'll have to see how it holds up over time.
Thank you for purchasing our product and for sharing your experience with us. Team SlipDoctors