Anti-Slip Spray for Fiberglass and Acrylic



  • $55.00

Non-Slip Spray works effectively on Fiberglass, Acrylic and most other surfaces. Available in Clear or White. Our Non-Slip spray is the highest rated aerosol spray for fiberglass/acrylic found on the market! SlipDoctors Non-Slip Spray is an epoxy aerosol that provides a hard, textured finish to help to prevent slip-and-fall accidents. It is barefoot friendly, lead-free, and chemical, gas and oil resistant.

It is ideal for both interior and exterior surfaces, it is designed for areas where water is present or slippery conditions exist such as fiberglass and acrylic bathtubs and showers, properly prepared wood, concrete, metal, tile, porcelain/ceramic and many other surfaces. This convenient aerosol spray is the perfect solution to treat small or irregularly shaped surfaces where increased traction is desired. One can covers up to 15 sq. ft.

Even when wet, your slippery floor’s slip resistance after the non-slip solution will surpass ANSI A137.1, A326.3 or B101.3 standards.

0.43 Wet DCOF - ANSI B101.3
0.45 Wet DCOF – ANSI A137.1 / A326.3
0.65 Wet SCOF - ANSI B101.1

Pendulum Test Values - Slider #55 
DRY -96 WET -53 - Slip Risk - LOW

Safety Data Sheet (SDS)
Technical Data Sheet (TDS)
Installation Instructions Testing Document

Suggested Uses

- Fiberglass & Acrylic Bathtubs / Showers
Onyx Shower bases
- Kitchens & Bathrooms
- Pool Decks, Ladders & Steps
- Boats & Trailers
- Gyms & Spas
- Hotels & Resorts
- Residential & Commercial Use

    Single Case
    Coverage per Sq Ft 15 180
    Cost per Sq Ft (Appx.) $2.33 $2.13

    • One can of SlipDoctors Non-Slip Spray
    • Painter‘s Tape
    • Painter’s Paper

    Note: for porcelain bathtubs, please repair any chips prior to application. Repair kits can be purchased at your local home improvement store


    Note: we do not recommend using black sandpaper, as it can leave behind small black dots that may be visible after using the clear spray

    Always test a small area for color compatibility and adhesion. Fiberglass/Acrylic:Lightly sand with 220 grit sand paper to promote adhesion.

    Clean surface with soap and water or wipe with clean cloth and lacquer thinner (or another cleaner that does not leave a lm or residue) to remove all sanding dust. Allow to dry thoroughly. For other surface preparation instructions, please visit the technical page on


    Step 1: Surface should be dry, clean and free of oil, wax, dirt, loose paint and other contaminants.
    Step 2: After entire surface is completely dry, properly ventilate room by opening windows, doors, turning on ceiling fans, etc.
    Step 3: Tape off application area with painter’s tape.
    Step 4: Mix contents of can well by shaking until the ball rattles within the can. Once ball rattles, continue to shake vigorously for 2-3 minutes. During use, shake intermittently for 10 seconds to keep product mixed.
    Step 5: Use painter’s paper to protect surround-ing areas from overspray. (Figure B)Spray 6 - 12 inches away from surface in a sweeping motion during application. Applying 2-3 light coats will cure, protect and look better than one heavy coat.
    Step 6: If spray stops or is irregular, turn can upside down and spray for 2-3 seconds to clear nozzle. Wipe tip, shake can and resume.
    Step 7: Slowly remove all tape and paper shortly after application. Allow 24 hours before use to allow product to fully cure. If product will be subject to prolonged periods of soaking in water, allow 48 hours before use to fully cure.


    • Remove overspray with paint thinner or lacquer thinner.
    IMPORTANT: Before storing partial can, clean valve immediately after use. To clean, hold can upside down and spray until only clear gas comes out (approximately 3 - 5 seconds), then wipe tip and store.
    • If spray valve becomes clogged, pull off and clean in lacquer thinner. Replace spray valve pointing opening away from body.
    • If desired to remove product, use acetone. For more details, refer to the Non-Slip Spray Clear and White Technical Data Sheet.

    Customer Reviews

    Based on 185 reviews
    Edward H.
    Good product

    This was a great solution for our shower. It applies well and is fairly transparent.

    I had a serious problem

    I had a serious problem (self-inflicted) on the floor of my Sterling bathtub made from Vikrell. I erroneously used an abrasive cleaner and the effect was horrendous. I called Sterling and was told they had nothing available to correct this problem. I could not accept this response, so I searched the Web and found and contacted Slip Doctors.
    I explained my situation, they answered my questions to my complete satisfaction, and suggested their Non-Slip Spray. I purchased the Spray, followed the directions, and covered with three light sprays.
    The Non-Slip Spray worked beautifully and I could not be more pleased and satisfied with the product and their customer service.

    Thank you for taking the time to review our product and service. Team SlipDoctors

    David M.
    did the job

    It worked, but holy cow was it smelly. The smell permeated the whole house for like 2 days.

    Thank you for taking the time to share your feedback. Team SlipDoctors

    Karen P.
    Solved slippery tub

    This definitely worked but very stinky so open a window. It didn’t discolor and kept me from slipping.

    Thank you for purchasing our product and for sharing your experience with us. Team SlipDoctors

    Customers Who Purchased This Item Also Viewed



    Sold Out